Equal Pipe Tee technical overview.
Equal Pipe Tee from JINYI is presented in the NPS 4 · equal tee configuration. Use the dimension schedule, connection details and inspection requirements below when comparing this product with your pipework or equipment drawing.
On this page
What is a equal pipe tee?
A equal pipe tee creates a T-shaped junction with equal nominal sizes on its run and branch. List all three connection sizes in the enquiry so the intended arrangement is clear.
Key dimensions and installation fit
Match every weld end to the required pipe outside diameter, wall schedule and bore. Centre-to-end dimensions determine the spool layout. For reducing fittings, state the larger run or inlet first and the smaller branch or outlet second; both end dimensions are needed to avoid selecting a fitting that matches only one connection. If the branch has a smaller nominal size than the run, compare the reducing pipe tee and identify each connection in the enquiry.
How to specify the equal pipe tee
Specify the material grade, pipe schedule, weld preparation and inspection requirements together. Carbon-steel and stainless-steel wall schedules may differ even when the nominal size is the same. The fitting geometry does not replace the line design, corrosion allowance or welding procedure required for the operating service.
Technical data for the equal pipe tee
| Nominal size | 4 in / DN100 |
|---|---|
| Run outside diameter | 114.3 mm |
| Branch outside diameter | 114.3 mm |
| Run centre-to-end C | 105 mm |
| Branch centre-to-end M | 105 mm |
| Branch angle | 90° |
Sizes and dimensional requirements
The dimensional schedule identifies the illustrated configuration. Compare each value with the mating pipe, equipment or support drawing. A nominal designation does not replace the actual connection diameter, installation envelope or mounting detail. The choices above let you include a different configuration with your quotation request.
Dimensions and tolerance schedule
| End diameter at NPS 4 | ±1.6 mm |
|---|---|
| Centre-to-end / length | ±2 mm |
Inspection, standards and documentation
Check end diameter, length or centre dimensions, wall thickness at the weld ends and the orientation of each outlet. Confirm the bevel and root-face detail against the welding procedure. Include material traceability, visual examination and any additional non-destructive examination required by the order.
State the required product standard and edition, material records and inspection acceptance criteria before ordering. Where pressure, temperature, movement or load are relevant, provide the operating and test conditions together. Document requirements should identify the actual component and drawing revision; a general certificate does not replace a dimensional or material record for the ordered item. For production steps and inspection considerations, see flanges and fittings manufacturing.
Where the equal pipe tee is used
- Fabricated pipe spools. Use weld-end diameter, wall schedule and centre dimensions to prepare the spool drawing.
- Process piping. Select material and inspection scope against the line specification.
- Replacement fittings. Compare both end dimensions and branch orientation with the existing installation.
How to order a equal pipe tee
Select the required options and send the quantity, destination, material and controlled drawing to JINYI. Include changed dimensions, mating details, finish, marking and packing requirements. The quotation defines the final configuration, inspection scope and delivery terms so the component can be checked against the intended installation.
Quantity prices and order preparation
| 50–199 pcs | US$3.47 per piece |
|---|---|
| 200–499 pcs | US$2.67 per piece |
| 500 pcs and above | US$1.56 per piece |
Freight and taxes are quoted separately. A different material, size or drawing can change the price and delivery requirements. Confirm the agreed specification before manufacture, and keep the drawing revision, selected options and ordered quantity together in the enquiry.
Other JINYI products worth comparing
Compare 90 degree pipe elbow, 45 degree pipe elbow, or review the pipe fittings and elbows catalog for other connection and configuration choices.
Request a custom equal pipe tee quotation from JINYI with the drawing and quantity required for your project.
Equal Pipe Tee selection and quotation checklist
The branch matches the run size in this tee arrangement. Give wall schedule and end preparation for each connection and check centre-to-end lengths against the piping layout. Use the photographed product form to identify the arrangement, then use the controlled drawing to define what will be supplied. Similar-looking components can have different end details, load paths or maintenance requirements.
Equal Pipe Tee dimensions and tolerances
The first comparison for this equal pipe tee is equal branch and run dimensions. Mark the dimensions that control mating, alignment and installation space on the enquiry drawing. Give units for every value and identify the datum from which it is measured. If a dimension is critical, specify its individual tolerance and measurement method rather than relying on a general tolerance note.
The current schedule identifies nominal size: 4 in / DN100; run outside diameter: 114.3 mm; branch outside diameter: 114.3 mm. Read these entries together with the configuration and tolerance tables above. Reference or example values describe the displayed arrangement; the approved JINYI quotation and drawing define the ordered component. A different interface, material or service condition needs a fresh comparison.
Prepare the material and interface information
For a equal pipe tee enquiry, identify the required material designation and supplied condition. Describe the mating components, attachment method and environment. Include the operating temperature and any relevant pressure, movement or structural load. These inputs should describe the actual installation, including changes between normal operation, start-up and maintenance where applicable.
Specify coatings, surface finish and marking separately from the base material. If traceability is needed, identify the record required and how it must correspond to the delivered component. Agree whether inspection covers dimensions, material documentation, welds or functional testing; these are different checks with different acceptance criteria.
Custom equal pipe tee quotation
Attach the latest drawing revision, required quantity and delivery destination when contacting JINYI. Highlight departures from the illustrated arrangement, including changed dimensions, connections, finish and packing. For repeat orders, reference the approved configuration and list changes explicitly so an earlier drawing is not assumed to remain current.
The three price tiers above organise the displayed quantity bands. Compare quotes using the same drawing, material, inspection scope and unit of supply. A piece, a segment and a complete assembly are different units where applicable. Confirm freight, taxes, documentation and delivery terms with the final quotation instead of inferring them from the displayed unit price.
Compare related component arrangements
Evaluate this equal tee by its actual equal branch and run dimensions and the required pipe tee arrangement. The photographs below show separate JINYI products for comparison. They are linked to their own technical pages and are not additional gallery views of this equal pipe tee.
| Photo | Related product | Selection detail |
|---|---|---|
 | Reducing Pipe Tee | Run diameter and branch transition. Compare this separate product when the drawing requires its particular arrangement. |
 | Pipe Cross | Outlet geometry and end preparation. Compare this separate product when the drawing requires its particular arrangement. |
 | Grooved Equal Tee | Run diameter and branch geometry. Compare this separate product when the drawing requires its particular arrangement. |
Questions to resolve before ordering
Which dimensions need checking first?
Start with equal branch and run dimensions and the mating or mounting detail. Check nominal designations against measured dimensions, then review the installation envelope. Photographs help identify the form; the drawing provides the dimensional basis for acceptance.
What should the quotation include?
A equal pipe tee quotation should identify the configuration, drawing revision, material, quantity, price basis and agreed inspection records. Keep these details together with the approved order so receiving inspection can compare the delivered product with the specified component.
Independent terminology reference
ASME butt weld fitting standard scope provides an independent reference for component terminology. Use the specified standard and edition where required by the project. This link does not establish JINYI certification, product approval or interchangeability with another manufacturer.
- 4 in / DN100
- Nominal size
- 114.3 mm
- Run outside diameter
- ±1.6 mm
- Tolerance
- 3
- Quantity tiers
- End matching — Outside diameter, bore and wall thickness define the pipe interface.
- Geometry control — Centre-to-end dimensions establish the assembled spool length.
- Weld preparation — Bevel, root face and transition details follow the selected welding specification.
At a glance
- Product
- Equal Pipe Tee
- Configuration
- NPS 4 · equal tee
- Nominal size
- 4 in / DN100
- Run outside diameter
- 114.3 mm
- Branch outside diameter
- 114.3 mm
Dimensions and technical specification
| Parameter | Specification |
|---|---|
| Nominal size | 4 in / DN100 |
| Run outside diameter | 114.3 mm |
| Branch outside diameter | 114.3 mm |
| Run centre-to-end C | 105 mm |
| Branch centre-to-end M | 105 mm |
| Branch angle | 90° |
