Solid Disc Blank technical overview.
Solid Disc Blank from JINYI is specified by its application, material and connection or drawing requirements. Review the selection schedule and enquiry requirements below to prepare a quotation for your project.
On this page
Specification basis: The schedule below distinguishes industry geometry from order-specific requirements. Final dimensions, performance and price are defined in the approved quotation and drawing. Photographs identify the product family.
What is a solid disc blank?
A solid disc blank is a circular metal component supplied without a through bore. Its thickness and outside diameter form the manufacturing envelope for covers, machined plates or other custom circular components.
Key dimensions and installation fit
Define the disc diameter, thickness, edge condition and subsequent machining requirements. Net plate weight excludes cutting losses, rough stock allowance and additional machining; it is not a finished-part cost. Compare related configurations: machined ring blank, flat circular tank cover.
How to specify the solid disc blank
Specify whether the supplied disc is rough, faced or fully machined. Identify the final bore or hole pattern only when those operations are part of the order. Solid discs and blind flanges are different purchase descriptions; a blind flange requires defined drilling, facing and a design basis.
Identify the stock form and the stage of manufacture: cut blank, rough-machined part or finished component. Overall diameter, bore, thickness and any segment angle establish the basic geometry. Datum locations, allowances and machining sequence determine how the blank becomes the final part.
Technical data for the solid disc blank
| Product form | Solid circular blank |
|---|---|
| Outside diameter | Finished and stock diameters to drawing |
| Bore | No through bore for the solid-disc form |
| Axial thickness | Finished and stock thicknesses to drawing |
| Centre form | Solid unless a bore or pilot hole is specified |
| Material grade | Specify carbon, alloy or stainless steel and supplied condition |
| Machining allowance | Agreed for each machined surface |
| Tolerance basis | Individual drawing limits; general class only when specified |
| Mass and quotation | Calculated from the confirmed geometry and material |
Sizes and dimensional requirements
Use the named standard for standardized interfaces and the controlled drawing for custom dimensions. Confirm units, diameter datums, minimum finished thickness and any mating-component requirements. A catalogue dimension is not a universal tolerance, capacity or pressure rating.
Dimensions and tolerance schedule
| Individually toleranced features | Limits and datum system on the approved drawing |
|---|---|
| General tolerances | Standard, edition and class apply only when specified |
| Functional acceptance | Agreed inspection method and acceptance criteria |
Individually toleranced dimensions and functional requirements take precedence over a general tolerance note. Specify the governing standard and acceptance method in the order documents; a tolerance shown by another manufacturer does not establish JINYI manufacturing capability.
Materials, inspection and documentation
Check the drawing revision, stock dimensions, edge condition and material identification. Record dimensions before and after machining where allowances are specified. For split or segmented parts, agree whether inspection is performed free or assembled. Holes, sealing faces, joining hardware and heat treatment must be specified separately.
State the exact material designation and supplied condition, the controlled drawing revision and the required inspection reports before ordering. Separate material certification from dimensional checks and functional or pressure testing. Agree the acceptance limits for the ordered component and identify any additional witnessing, marking or packing requirements. Use the custom manufacturing and OEM guidance to prepare the drawing-defined supply scope.
Installation and handling guidance
Preserve the identification mark when turning or drilling the blank. Define lifting and clamping methods appropriate to its mass and section. Any later use as a pressure-retaining cover requires the complete cover design, rather than visual similarity to a flange.
Where the solid disc blank is used
- Machining stock. Drawing-defined rings and discs for subsequent boring, turning or drilling.
- Equipment fabrication. Custom interfaces, spacer parts and shaped assembly components.
- Replacement parts. Controlled geometry for comparison with the existing component and mating surfaces.
How to order a solid disc blank
Send the required configuration, material, quantity, destination and controlled drawing to JINYI. Identify changed dimensions, mating components, operating conditions and inspection scope. For a repeat order, include the previous approved revision and state any changes. The final quotation defines the supplied geometry, documentation, price and delivery terms.
Quantity prices and order preparation
| 1–9 pcs | US$20.00 / piece |
|---|---|
| 10–49 pcs | US$20.00 / piece |
| 50+ pcs | US$20.00 / piece |
Indicative budget pricing selected from public supplier listings. Selected lower amount from DHDZ's US$20–5,000 custom forged-disc listing. This does not price an unspecified finished diameter and thickness. DHDZ customized forged-disc listing. Final JINYI pricing depends on the confirmed specification, quantity, inspection and delivery scope. Quantity-specific terms are confirmed with the final quotation.
Engineering and pricing references
APPORO general machining tolerance guidance; CMEC Wuxi forging listings. These sources explain the named product geometry or selection method. Their certifications, rated capacities and manufacturing capabilities belong to the named organizations.
Other JINYI products worth comparing
Review the industrial pipe flanges catalog for adjoining components, connection choices and alternative product forms.
Request a solid disc blank quotation from JINYI with the drawing, material and quantity required for your project.
Solid Disc Blank selection and quotation checklist
The blank is solid at the centre. Specify any later bore or profile separately and distinguish the ideal geometric mass from the weight of rough material supplied for machining. Use the photographed product form to identify the arrangement, then use the controlled drawing to define what will be supplied. Similar-looking components can have different end details, load paths or maintenance requirements.
Solid Disc Blank dimensions and tolerances
The first comparison for this solid disc blank is disc thickness and stock allowance. Mark the dimensions that control mating, alignment and installation space on the enquiry drawing. Give units for every value and identify the datum from which it is measured. If a dimension is critical, specify its individual tolerance and measurement method rather than relying on a general tolerance note.
Define the disc diameter, thickness, edge condition and subsequent machining requirements. Net plate weight excludes cutting losses, rough stock allowance and additional machining; it is not a finished-part cost. Review the selection schedule together with the final drawing and inspection requirements.
Prepare the material and interface information
For a solid disc blank enquiry, identify the required material designation and supplied condition. Describe the mating components, attachment method and environment. Include the operating temperature and any relevant pressure, movement or structural load. These inputs should describe the actual installation, including changes between normal operation, start-up and maintenance where applicable.
Specify coatings, surface finish and marking separately from the base material. If traceability is needed, identify the record required and how it must correspond to the delivered component. Agree whether inspection covers dimensions, material documentation, welds or functional testing; these are different checks with different acceptance criteria.
Custom solid disc blank quotation
Attach the latest drawing revision, required quantity and delivery destination when contacting JINYI. Highlight departures from the illustrated arrangement, including changed dimensions, connections, finish and packing. For repeat orders, reference the approved configuration and list changes explicitly so an earlier drawing is not assumed to remain current.
Compare quotations using the same geometry, grade, supplied condition, unit of supply and inspection scope. A piece, a segment and a complete assembly can represent different quantities. Confirm quantity discounts and delivery terms with the final quotation.
Compare related component arrangements
Evaluate this disc blank by its actual disc thickness and stock allowance and the required steel disc arrangement. The photographs below show separate JINYI products for comparison. They are linked to their own technical pages and are not additional gallery views of this solid disc blank.
| Photo | Related product | Selection detail |
|---|---|---|
 | Machined Ring Blank | Ring diameters and machining allowance. Compare this separate product when the drawing requires its particular arrangement. |
 | Heat Exchanger Tube Sheet | Tube pitch and hole geometry. Compare this separate product when the drawing requires its particular arrangement. |
 | Profiled Ring Blank | Recess depth and remaining thickness. Compare this separate product when the drawing requires its particular arrangement. |
Questions to resolve before ordering
Which dimensions need checking first?
Start with disc thickness and stock allowance and the mating or mounting detail. Check nominal designations against measured dimensions, then review the installation envelope. Photographs help identify the form; the drawing provides the dimensional basis for acceptance.
What should the quotation include?
A solid disc blank quotation should identify the configuration, drawing revision, material, quantity, price basis and agreed inspection records. Keep these details together with the approved order so receiving inspection can compare the delivered product with the specified component.
Independent terminology reference
ASME flange standard scope provides an independent reference for component terminology. Use the specified standard and edition where required by the project. This link does not establish JINYI certification, product approval or interchangeability with another manufacturer.
- Spec
- Defined configuration
- Grade
- Material requirement
- US$20.00
- Indicative unit price
- 3
- Quantity bands
- Product arrangement — Solid circular blank
- Engineering selection — Define the disc diameter, thickness, edge condition and subsequent machining requirements. Net plate weight excludes cutting losses, rough stock allowance and additional machining; it is not a finished-part cost.
- Quotation scope — Material, drawing revision, quantity, inspection and delivery terms confirmed together
At a glance
- Product form
- Solid circular blank
- Product form
- Solid circular blank
- Outside diameter
- Finished and stock diameters to drawing
- Bore
- No through bore for the solid-disc form
- Pricing
- Indicative USD pricing
| Product form | Solid circular blank |
|---|---|
| Outside diameter | Finished and stock diameters to drawing |
| Bore | No through bore for the solid-disc form |
| Axial thickness | Finished and stock thicknesses to drawing |
| Centre form | Solid unless a bore or pilot hole is specified |
| Material grade | Specify carbon, alloy or stainless steel and supplied condition |
| Machining allowance | Agreed for each machined surface |
| Tolerance basis | Individual drawing limits; general class only when specified |
| Mass and quotation | Calculated from the confirmed geometry and material |
| Individually toleranced features | Limits and datum system on the approved drawing |
|---|---|
| General tolerances | Standard, edition and class apply only when specified |
| Functional acceptance | Agreed inspection method and acceptance criteria |
