Fabricated Support Frame technical overview.
Fabricated Support Frame from JINYI is specified by its application, material and connection or drawing requirements. Review the selection schedule and enquiry requirements below to prepare a quotation for your project.
On this page
Specification basis: The schedule below distinguishes industry geometry from order-specific requirements. Final dimensions, performance and price are defined in the approved quotation and drawing. Photographs identify the product family.
What is a fabricated support frame?
A fabricated support frame is a welded structural assembly that provides mounting and load-transfer points for equipment or pipe support components. The frame geometry, connection locations and design reactions are defined by the project drawing.
Key dimensions and installation fit
The frame envelope does not determine its capacity. Member sizes, bracing, welds, base plates and anchors must be checked for the actual load cases and installation. Quote the completed fabrication scope rather than applying one price to all frames. Compare related configurations: welded pipe shoe, pipe saddle support.
How to specify the fabricated support frame
Provide the plan dimensions, height, section sizes and all supported reactions. Identify fixed and removable joints, base-plate locations, lifting points and installation sequence. Frame stiffness and foundation interfaces should be included in the assembly review.
Define the frame envelope, section sizes, mounting pattern and the exact points where equipment loads enter the frame. Include vertical and lateral reactions, eccentricity, vibration and anchor conditions. The dimensions shown here are a sample drawing schedule and do not establish structural capacity.
Technical data for the fabricated support frame
| Product form | Welded structural support frame |
|---|---|
| Overall dimensions | Length, width and height to project drawing |
| Supported equipment | Identify mass, centre of gravity and attachment points |
| Design actions | Vertical, lateral, dynamic and other applicable load cases |
| Members and bracing | Section sizes and grades to structural calculation |
| Base plates and anchors | To connection and supporting-structure design |
| Weld requirements | Joint detail, procedure and examination scope |
| Dimensional acceptance | Datums, level, flatness and hole positions to drawing |
| Surface protection | Coating or galvanizing system as specified |
| Documentation | Agreed drawing, inspection and material records |
Sizes and dimensional requirements
Use the named standard for standardized interfaces and the controlled drawing for custom dimensions. Confirm units, diameter datums, minimum finished thickness and any mating-component requirements. A catalogue dimension is not a universal tolerance, capacity or pressure rating.
Dimensions and tolerance schedule
| Individually toleranced features | Limits and datum system on the approved drawing |
|---|---|
| General tolerances | Standard, edition and class apply only when specified |
| Functional acceptance | Agreed inspection method and acceptance criteria |
The frame envelope does not determine its capacity. Member sizes, bracing, welds, base plates and anchors must be checked for the actual load cases and installation. Quote the completed fabrication scope rather than applying one price to all frames.
Materials, inspection and documentation
Check overall dimensions, base positions, squareness and equipment interfaces. Specify weld symbols and examination, material records and coating requirements. Identify machining after welding where mounting faces require alignment. Include anchors and the supporting substrate in the final installation design.
State the exact material designation and supplied condition, the controlled drawing revision and the required inspection reports before ordering. Separate material certification from dimensional checks and functional or pressure testing. Agree the acceptance limits for the ordered component and identify any additional witnessing, marking or packing requirements. Use the pipe support and casing manufacturing guidance to confirm fabrication and inspection requirements.
Installation and handling guidance
Check diagonal dimensions, base-plate flatness and connection positions before fixing the frame. Use the specified anchor and grout detail. Frame alignment should be established independently of the attached pipework so that the pipe does not become an unintended locating tool.
Where the fabricated support frame is used
- Equipment mounting. Drawing-defined bases for machinery and pipe support assemblies.
- Support fabrication. Load paths coordinated with adjoining steelwork and foundations.
- Plant modifications. Geometry checked against the available installation envelope.
How to order a fabricated support frame
Send the required configuration, material, quantity, destination and controlled drawing to JINYI. Identify changed dimensions, mating components, operating conditions and inspection scope. For a repeat order, include the previous approved revision and state any changes. The final quotation defines the supplied geometry, documentation, price and delivery terms.
Quantity prices and order preparation
| 1–9 pcs | US$100.00 / piece |
|---|---|
| 10–49 pcs | US$100.00 / piece |
| 50+ pcs | US$100.00 / piece |
Indicative budget pricing selected from public supplier listings. Uses the advertised US$100 frame sample amount as an indicative reference. Frame size, sections, load cases, coating and inspection are quoted to drawing. Changwei fabricated frame listing. Final JINYI pricing depends on the confirmed specification, quantity, inspection and delivery scope. Quantity-specific terms are confirmed with the final quotation.
Engineering and pricing references
WeldingFabrication support fabrication guide; APPORO general machining tolerance guidance. These sources explain the named product geometry or selection method. Their certifications, rated capacities and manufacturing capabilities belong to the named organizations.
Other JINYI products worth comparing
Review the pipe supports and hangers catalog for adjoining components, connection choices and alternative product forms.
Request a fabricated support frame quotation from JINYI with the drawing, material and quantity required for your project.
Fabricated Support Frame selection and quotation checklist
The fabricated frame carries loads through its members and base connections. Provide member sizes, bracing, fixing details and the load cases that govern the structure. Use the photographed product form to identify the arrangement, then use the controlled drawing to define what will be supplied. Similar-looking components can have different end details, load paths or maintenance requirements.
Fabricated Support Frame dimensions and tolerances
The first comparison for this fabricated support frame is frame geometry and base fixings. Mark the dimensions that control mating, alignment and installation space on the enquiry drawing. Give units for every value and identify the datum from which it is measured. If a dimension is critical, specify its individual tolerance and measurement method rather than relying on a general tolerance note.
The frame envelope does not determine its capacity. Member sizes, bracing, welds, base plates and anchors must be checked for the actual load cases and installation. Quote the completed fabrication scope rather than applying one price to all frames. Review the selection schedule together with the final drawing and inspection requirements.
Prepare the material and interface information
For a fabricated support frame enquiry, identify the required material designation and supplied condition. Describe the mating components, attachment method and environment. Include the operating temperature and any relevant pressure, movement or structural load. These inputs should describe the actual installation, including changes between normal operation, start-up and maintenance where applicable.
Specify coatings, surface finish and marking separately from the base material. If traceability is needed, identify the record required and how it must correspond to the delivered component. Agree whether inspection covers dimensions, material documentation, welds or functional testing; these are different checks with different acceptance criteria.
Custom fabricated support frame quotation
Attach the latest drawing revision, required quantity and delivery destination when contacting JINYI. Highlight departures from the illustrated arrangement, including changed dimensions, connections, finish and packing. For repeat orders, reference the approved configuration and list changes explicitly so an earlier drawing is not assumed to remain current.
Compare quotations using the same geometry, grade, supplied condition, unit of supply and inspection scope. A piece, a segment and a complete assembly can represent different quantities. Confirm quantity discounts and delivery terms with the final quotation.
Compare related component arrangements
Evaluate this support frame by its actual frame geometry and base fixings and the required steel frame arrangement. The photographs below show separate JINYI products for comparison. They are linked to their own technical pages and are not additional gallery views of this fabricated support frame.
| Photo | Related product | Selection detail |
|---|---|---|
 | Welded Pipe Shoe | Shoe height and attachment welds. Compare this separate product when the drawing requires its particular arrangement. |
 | Gusseted Riser Pipe Support | Gusset geometry and support load. Compare this separate product when the drawing requires its particular arrangement. |
 | Pipe Saddle Support | Saddle curvature and elevation. Compare this separate product when the drawing requires its particular arrangement. |
Questions to resolve before ordering
Which dimensions need checking first?
Start with frame geometry and base fixings and the mating or mounting detail. Check nominal designations against measured dimensions, then review the installation envelope. Photographs help identify the form; the drawing provides the dimensional basis for acceptance.
What should the quotation include?
A fabricated support frame quotation should identify the configuration, drawing revision, material, quantity, price basis and agreed inspection records. Keep these details together with the approved order so receiving inspection can compare the delivered product with the specified component.
Independent terminology reference
LISEGA pipe support selection families provides an independent reference for component terminology. Use the specified standard and edition where required by the project. This link does not establish JINYI certification, product approval or interchangeability with another manufacturer.
- Spec
- Defined configuration
- Grade
- Material requirement
- US$100.00
- Indicative unit price
- 3
- Quantity bands
- Product arrangement — Fabricated support frame · project drawing
- Engineering selection — The frame envelope does not determine its capacity. Member sizes, bracing, welds, base plates and anchors must be checked for the actual load cases and installation. Quote the completed fabrication scope rather than applying one price to all frames.
- Quotation scope — Material, drawing revision, quantity, inspection and delivery terms confirmed together
At a glance
- Product form
- Fabricated support frame · project drawing
- Product form
- Welded structural support frame
- Overall dimensions
- Length, width and height to project drawing
- Supported equipment
- Identify mass, centre of gravity and attachment points
- Pricing
- Indicative USD pricing
| Product form | Welded structural support frame |
|---|---|
| Overall dimensions | Length, width and height to project drawing |
| Supported equipment | Identify mass, centre of gravity and attachment points |
| Design actions | Vertical, lateral, dynamic and other applicable load cases |
| Members and bracing | Section sizes and grades to structural calculation |
| Base plates and anchors | To connection and supporting-structure design |
| Weld requirements | Joint detail, procedure and examination scope |
| Dimensional acceptance | Datums, level, flatness and hole positions to drawing |
| Surface protection | Coating or galvanizing system as specified |
| Documentation | Agreed drawing, inspection and material records |
| Individually toleranced features | Limits and datum system on the approved drawing |
|---|---|
| General tolerances | Standard, edition and class apply only when specified |
| Functional acceptance | Agreed inspection method and acceptance criteria |
